Gene Vogel, EASA Pump & Vibration Specialist

• ASA ASC-S2 Work Group 15 - Shaft Alignment Methodology (acting chair)

Tom Bishop, PE, EASA Senior Technical Support Specialist

• CSA 392 Subcommittee on Motor Refurbishment, Testing of three-phase cage induction motors during refurbishment

Frederic Beghain, EASA Region 9 General Manager

John Allen, Sheppard Engineering Limited

• Working Group for Introduction of IEC 60079-19 into IEC Ex Scheme
• TC31 Management Committee for IEC 60079-19

Tom Bishop, PE, EASA Senior Technical Support Specialist

• Maintenance Team 60079-1 for IEC 60079-1, Electrical Apparatus for Explosive Gas Atmospheres
• TC31 US TAG for IEC 60079, 61779, 62013 and 62086

Mike Howell, PE, EASA Technical Support Specialist

• USNC TAG for IEC SC22G, Adjustable Speed Electric Drive Systems Incorporating Semiconductor Power Converters

Chuck Yung, EASA Senior Technical Support Specialist

• TC2 working group
• IEC 60034-8 Rotating Electrical Machines; Terminal Markings
• IEC 60034-11 Rotating electrical machines – thermal protection
• IEC 60034-17 Motors fed from converters
• IEC 60035-2-34 Standards Technical Panel for Hermetic Refrigerant Motor-Compressors
• IEC 60034-27 Rotating electrical machines – Part 27: Partial discharge off-line measurements on the stator winding insulation of rotating machinery

IEEE Working Groups

Chuck Yung, EASA Senior Technical Support Specialist

• IEEE 115 Test Procedures for Synchronous Machines
• IEEE 303 Recommended Practice for Auxiliary Devices for Rotating Electrical Machines in Class I, Division 2 and Zone 2 Locations and Class II, Division 2 and Zone 22 Locations
• IEEE 841-1 (North America) & 841-2 (International) Standard for the Petroleum and Chemical Industry - Severe Duty Totally Enclosed Fan-Cooled (TEFC) Electric Motors
• IEEE 1017-2013 Recommended Practice for Field Testing Electrical Submersible Cable
• IEEE 1018 Recommended Practice for Specifying Electric Submersible Pump Cable - Ethylene Propylene Rubber Insulation
• IEEE 1019 Recommended Practice for Specifying Electric Submersible Pump Cable - Polypropylene Insulation
• IEEE 1068 Standard for the Repair and Rewinding of Electric Motors for the Petrochemical and Other Process Industries (chair)
• IEEE 1349 Motors in Hazardous Locations
• IEEE 1458 Recommended Practice for the Selection, Field Testing and Life Expectancy of Molded Case Circuit Breakers for Industrial Applications
• IEEE 1566 Standard for Performance of Adjustable Speed AC Drives Rated 375 kW and Larger
• IEEE 1584 Guide for Performing Arc-Flash Hazard Calculations
• IEEE 1683 Guide for Motor Control Centers Rated Up to and Including 600v AC or 1000v DC with Recommendations Intended to Help Reduce Electrical Hazards
• IEEE 1716 Recommended Practice for Managing Natural Disaster Impact of Key Electrical Systems and Installations in Petroleum and Chemical Facilities
• IEEE 1814 Recommended Practice for Electrical System Design Techniques to Improve Electrical Safety
• IEEE 2455 Repair Guide for DC Machines (chair)

​Mike Howell, PE, EASA Technical Support Specialist

• IEEE P114 Standard Test Procedure for Single-Phase Induction Motors
• IEEE 1415 Guide for Induction Machinery Maintenance Testing
• IEEE Standard 11-2006, Rotating Electric Machinery for Rail and Road Vehicles

IEEE Standards Association—Standards Review and Ballot

Tom Bishop, PE, EASA Senior Technical Support Specialist

• IEEE C37.102 Guide for AC Generator Protection 
• IEEE C57.12.00 Standard for the General Requirements for Liquid-Immersed Distribution, Power, and Regulating Transformers
• IEEE C57.12.90 Standard Test Code for Liquid-Immersed Distribution, Power, and Regulating Transformers
• IEEE C57.94 Recommended Practice for Installation, Application, Operation, and Maintenance of Dry-Type Distribution and Power Transformers
• IEEE 56 Guide for Insulation Maintenance of Electric Machines (Combines IEEE 56 and IEEE 432)
• IEEE 95 Recommended Practice for Insulation Testing of AC Electric Machinery with High Direct Voltage
• IEEE 112 Test Procedure for Polyphase Induction Motors and Generators
• IEEE 117 Standard Test Procedure for Thermal Evaluation of Systems of Insulating Materials for Random-Wound AC Electric Machinery
• IEEE 286 Recommended Practice for Measurement of Power Factor Tip-Up of Electric Machinery Stator Coil Insulation
• IEEE 1665 Guide for the Rewind of Synchronous Generators, 50 Hz and 60 Hz, Rated 1 MVA and Above
• IEEE 1812 Guide for Testing Permanent Magnet Machines 
• IEEE 3002.7 Recommended Practice for Conducting Motor-Starting Studies in Industrial and Commercial Power Systems
• IEEE 3002.8 Recommended Practice for Conducting Harmonic-Analysis Studies of Industrial and Commercial Power Systems

Linda Raynes, EASA President and CEO
Tom Bishop, PE, EASA Senior Technical Support Specialist

Chuck Yung, EASA Senior Technical Support Specialist

• ANSI C50 Rotating Machinery Committee (Alternate: Tom Bishop, P.E., EASA Senior Technical Support Specialist)

Tom Bishop, PE, EASA Senior Technical Support Specialist

• NEMA Codes and Standards (C&S) Task Force on Refurbishing Products

Mike Howell, PE, EASA Technical Support Specialist

• NEMA MW 1000

Tom Bishop, PE, EASA Senior Technical Support Specialist

• NFPA 70B Electrical Equipment Maintenance

Tom Bishop, PE, EASA Senior Technical Support Specialist

• 506 Low Voltage Transformers
• 1004 Standard for Electric Motors (7 sub-categories)
• 1446 Systems of Insulating Materials
• 1562 Transformers, Distribution, Dry-Type over 600 volts
• 2111 Standard for Overheating Protection for Motors 

Chuck Yung, EASA Senior Technical Support Specialist

• 448 Standard for Pumps for Fire Protection Service
• 674 Electric Motors and Generators for Hazardous Locations
• 778 Standard for Motor-Operated Water Pumps
• 840 Standard for Insulation Coordination Including Clearances and Creepage Distances for Electrical Equipment
• 1434 Standard for Thermistor-Type Devices
• 1450 Standard for Motor-Operated Air Compressors, Vacuum Pumps and Painting Equipment

Gene Vogel, EASA Pump & Vibration Specialist

• ANSI-ASA_S2-WG15 Committee for Shaft Alignment Standards (co-chair)